Mastering Plumbing Fundamentals When You Install a Bathtub
Mastering Plumbing Fundamentals When You Install a Bathtub
Blog Article
Every person has got their private conception on the subject of How to Install a Bathtub.
Setting up a bathtub isn't specifically rocket science, however it does need solid plumbing, woodworking, and also in some cases, tiling skills. Replacing an old tub with a new one is also a moderately challenging task. If the old bathtub is readily obtainable, the job can relocate rapidly; if you need to open up a wall surface to eliminate the old bathtub and position the brand-new bathtub, the task is much harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to move out the old tub and also embeded in the new one. Make sure you have actually certified yourself for the job and also are comfortable attempting it. Instead of employing a contractor to take over a halfway-completed project, it is better to think about employing one prior to you start. Possibilities are you might need a professional plumber to make tube connections.
This short article will help you set up a new tub in your shower room if you have actually already purchased a new tub and do not require to change the setup of your previous water pipelines.
Your tools and also product list should consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipelines. As soon as the supply pipelines have been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will need a plastic port to stop damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the tap as well as the sink. Secure the faucet in position with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Utilizing both wooden boards under its feet, put the bath tub in the called for setting. The wooden boards are practical in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as adjusting the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest flexible tap connector to the appropriate supply pipeline by making a compression join; then do the same for the various other faucet.
Activate the water system and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Load the bathtub as well as also examine the overflow electrical outlet as well as the normal outlet for leakages.
Finally, deal with the bathroom paneling as explained in the producer's instruction manual. Tiling as well as securing around the bathtub needs to wait up until the bath tub has been used at the very least when as this will certainly resolve it right into its last position.
Planning for the Installation
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid strain on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you make use of all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split a stiff seal, creating the water to pass through the wall in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are offered in tubes and cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water before sealing, to allow for the activity experienced when the tub remains in use. The sealant can fracture rather very early if you do not take into consideration this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very inquisitive about Installing A Bathtub and I hope you appreciated my article. Sharing is caring. Helping people is fun. Thanks a lot for your time. Visit us again soon.
Drips? Dial fast! Report this page